Harga Plat Mild Steel ASTM A-36

Characteristic

Mild Steel Plate, also known as Hot Rolled A36 Steel Plate is a structural quality steel plate used for a large variety of general construction and industrial applications. Mild Steel Plate ASTM A-36 is one of the most commonly used hot rolled general structural steel. Typical carbon steel materials, they are very cheap, excelling in weldability & machinability and they can be subjected to various heat treatments.

Availability
Supplied as plates, sheets, flats, bars, sections, etc.
Plate Thickness: 4.5 mm, 6 mm, 8 mm, 10 mm dan 12 mm
Size: 5′ x 20′ , 6′ x 20′ , 4′ x 8′
Size: Thickness x Width x Length

Specifications
Grade: ASTM A36, AISI A-36
Workability: Easy to Weld, Cut, Form and Machine

Mechanical Properties

  • Density (kg/m3): 7860
  • Young’s Modulus (GPa): 190-210
  • Tensile Strength (MPa): 400 – 510 MPa
  • Yield Strength (MPa): 205-245 MPa
  • Poisson’s ratio: 0.26
  • Brinell Hardness (HB) 160

Equivalents
DIN Equivalents for JIS SS400: 17100 St 44-2
ASTM Equivalents for JIS SS400: ASTM A36, ASTM A283 Grade D
EN Equivalents for JIS SS400: EN S275/ BS 43A

Chemical Composition (%)
Carbon (C), Silicon (Si) and Manganese (Mn) content are not controlled. Phosphorus (P) 0.05% Max and Sulphur (S) 0.05% Max have to controlled below these levels.

Tabel Ukuran & Berat Nominal Plat ASTM A-36:
Product Thickness (mm) Standard Sheet Size Weight per square metre
Mild Steel Plate 3mm 3.00 1200 x 2400mm (1.2 x 2.4m) 23.55
Mild Steel Plate 4mm 4.00 1200 x 2400mm (1.2 x 2.4m) 31.4
Mild Steel Plate 5mm 5.00 1200 x 2400mm (1.2 x 2.4m) 39.25
Mild Steel Plate 6mm 6.00 1200 x 2400mm (1.2 x 2.4m) 47.1
Mild Steel Plate 8mm 8.00 1200 x 2400mm (1.2 x 2.4m) 62.8
Mild Steel Plate 10mm 10.00 1200 x 2400mm (1.2 x 2.4m) 78.5
Mild Steel Plate 12mm 12.00 1200 x 2400mm (1.2 x 2.4m) 94.2
Mild Steel Plate 16mm 16.00 1200 x 2400mm (1.2 x 2.4m) 125.6
Mild Steel Plate 20mm 20.00 1200 x 2400mm (1.2 x 2.4m) 157
Mild Steel Plate 25mm 25.00 1200 x 2400mm (1.2 x 2.4m) 196.25
Melting Point
Melting point of SS400 is 1430 Degree Celsius
Applications:
base plates, gussets, liners, road plates, trench covers, etc.

Related Carbon Steel:

Iklan

Stainless Steel 310

Product : AISI 310
Kategori: Stainless Steel
Grades : Chromium-Nickel steel
Standard: Austenitic

Characteristic
AISI 310 is an Austenitic Standard grade Stainless Steel. It is commonly called AISI Type 310 Chromium-Nickel steel.

Stainless Steel 310 Technical Data

Chemical Composition: (%)

C Mn Si Cr Ni P S
0.25 2.00 1.50 24.0-26.0 19.0-22.0 0.045 0.03

Equivalent:
France: AFNOR Z 12 CNS 25.20
Germany: DIN 1.4841
Italy: UNI X 16 CrNiSi 25 20 , UNI X 22 CrNi 25 20
Japan: JIS SUS 310
United Kingdom: B.S. 310 S 24
United States: AMS 5694 , AMS 5695 , ASME SA182 , ASME SA213 , ASME SA249 , ASME SA312 , ASME SA358 , ASME SA403 , ASME SA409 , ASTM A167 , ASTM A182 , ASTM A213 , ASTM A249 , ASTM A276 , ASTM A312 , ASTM A314 , ASTM A358 , ASTM A403 , ASTM A409 , ASTM A473 , ASTM A511 , ASTM A580 , ASTM A632 , FED QQ-S-763 , FED QQ-S-766 , FED QQ-W-423 , FED STD-66 , MIL SPEC MIL-S-862 , SAE 30310 , SAE J405 (30310) , UNS S31000

Mechanical Properties
Density (×1000 kg/m3) 8
Poisson’s Ratio 0.27-0.30
Elastic Modulus (GPa) 200
Tensile Strength (Mpa) 515
Yield Strength (Mpa) 205
Elongation (%) 40
Reduction in Area (%) 50
Hardness (HRB) 95 (max)

Physical Properties
Thermal Expansion (10-6/ºC) 15.9
Thermal Conductivity (W/m-K) 14.2
Specific Heat (J/kg-K) 500
Electric Resistivity (10-9W-m) 780

Applications

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment

Product Stainless Steel:

Stainless Steel 304

Dear valued customers,

Beyond-Steel menjual Stainless Steel 304 acerinox,Jindal, Heisei, Outokumpu import plat, sheet, roundbar dan chanel dengan ukuran dan ketebalan bervariasi. Untuk informasi stock dan harga silahkan hubungi kami:

Tel  : +62-021-2986 1684

Fax : +62-021-2986 1684

Mobile: +62-0819 0804 5114

E-mail: sales@beyond-steel.com

Characteristic Grades 304

Stainless steel grade 304 is the most versatile and widely used stainless steel. It is still sometimes referred to by its old name 18/8 which is derived from the nominal composition of type 304 being 18% chromium and 8% nickel. Stainless steel types 1.4301 and 1.4307 are also known as grades 304 and 304L respectively.

Stainless steel 304 is an austenitic grade that can be severely deep drawn. This property has resulted in 304 being the dominant grade used in applications like sinks and saucepans.

Stainless steel 304L is the low carbon version of 304. It is used in heavy gauge components for improved weldability. Some products such as plate and pipe may be available as “dual certified” material that meets the criteria for both 304 and 304L. 304H, a high carbon content variant, is also available for use at high temperatures.

Property data given in this document is typical for flat rolled products covered by ASTM A240/A240M. ASTM, EN or other standards may cover products sold. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this datasheet.

Availability

Stainless steel 304 is available in Sheet, Bar, Wire, Rod, Strip, tube, pipe, and Channel, For all stock availability contact Sales.

Stainless steel 304 Sheet

Stainless steel 304 Plate

Stainless steel 304 Rod

Stainless steel 304 Tube

Stainless steel 304 Pipe

Stainless steel 304 Channel

Stainless Steel 304 Technical Data

Chemical Composition (%)

C : 0.05 – 0.08

Si : <= 1.0

Mn: <= 2.00

Ni : 8.00 – 11.00

Cr : 18.00 – 20.00

Tensile Strength (0.2%) : >= 53 Kgf/MM2

Yield Strength : >= 21 Kgf/MM2

Elongation : >= 40%

Hardness (HB) : <= 187 HB

Corrosion Resistance

304 has excellent corrosion resistance in a wide variety of environments and when in contact with different corrosive media. Pitting and crevice corrosion can occur in environments containing chlorides. Stress corrosion cracking can occur at temperatures over 60°C.
 
Heat ResistanceJustify Full304 has good resistance to oxidation in intermittent service up to 870°C and in continuous service to 925°C. However, continuous use at 425-860°C is not recommended if corrosion resistance in water is required. In this instance 304L is recommended due to its resistance to carbide precipitation.Where high strength is required at temperatures above 500°C and up to 800°C, grade 304H is recommended. This material will retain aqueous corrosion resistance.
 
Fabrication

Fabrication of all stainless steels should be done only with tools dedicated to stainless steel materials. Tooling and work surfaces must be thoroughly cleaned before use.These precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

Cold Working

304 stainless steel readily work hardens. Fabrication methods involving cold working may require an intermediate annealing stage to alleviate work hardening and avoid tearing or cracking. At the completion of fabrication a full annealing operation should be employed to reduce internal stresses

Hot Working

Fabrication methods, like forging, that involve hot working should occur after uniform heating to 1149-1260°C. The fabricated components should then be rapidly cooled to ensure maximum corrosion resistance.

Heat Treatment

304 stainless steel cannot be hardened by heat treatment. Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

Machinability

304 stainless steel has good machinability. Machining can be enhanced using the following rules:

  • Cutting edges must be kept sharp. Dull edges cause excess work hardening.
  • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.
  • Chip breakers should be employed to assist in ensuring swarf remains clear of the work
  • Low thermal conductivity of austenitic alloys results in heat concentrating at the cutting edges. This means coolants and lubricants are necessary and must be used in large quantities.
Welding

Fusion welding performance for type 304 stainless steel is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel. For 304L the recommended filler is 308L. Heavy welded sections may require post-weld annealing. This step is not required for 304L. Grade 321 may be used if post-weld heat treatment is not possible.

 

Tabel Ukuran dan Berat Plat stainless steel 304 4’x8′ Beyond-steel Indonesia:

Stainless Steel Size  Berat (Kg)
Plate 304 1 mm x 4′ x 8′ 23.6 Kg
Plate 304 2 mm x 4′ x 8′ 47.2 Kg
Plate 304 3 mm x 4′ x 8′ 70.8 Kg
Plate 304 4 mm x 4′ x 8′ 94.4 Kg
Plate 304 5 mm x 4′ x 8′ 118 Kg
Plate 304 6 mm x 4′ x 8′ 141.6 Kg
Plate 304 8 mm x 4′ x 8′ 188.8 Kg
Plate 304 10 mm x 4′ x 8′ 236 Kg
Plate 304 12mm x 4′ x 8′ 283.2 Kg

Applications

304 stainless steel is typically used in:

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment
  • Springs, nuts, bolts and screws
  • Medical implants

Related Stainless Steel:

Plat Kapal

Characteristic

JIS 3101 SS-400, known as SS400, in the ASME Code Section II-A & JIS specifications of steel plates for general structure included in the category of SA-36. In JIS (Japanese Industrial Standard) “SS” stands for structural steel and 400 grade which is similar to AISI 1018. SS400 is one of the most commonly used hot rolled general structural steel. Typical carbon steel materials, they are very cheap, excelling in weldability & machinability and they can be subjected to various heat treatments.
Availability
Supplied as plates, sheets, flats, bars, sections, etc.
Plate Thickness: 4.5 mm, 6 mm, 8 mm, 10 mm dan 12 mm
Size: 5′ x 20′ , 6′ x 20′ , 4′ x 8′

Mechanical Properties

  • Density (kg/m3): 7860
  • Young’s Modulus (GPa): 190-210
  • Tensile Strength (MPa): 400 – 510 MPa
  • Yield Strength (MPa): 205-245 MPa
  • Poisson’s ratio: 0.26

Hardness
Brinell Hardness (HB) 160

Equivalents
DIN Equivalents for JIS SS400: 17100 St 44-2
ASTM Equivalents for JIS SS400: ASTM A36, ASTM A283 Grade D
EN Equivalents for JIS SS400: EN S275/ BS 43A
Chemical Composition
As per JIS G 3101, Carbon (C), Silicon (Si) and Manganese (Mn) content are not controlled. Phosphorus (P) 0.05% Max and Sulphur (S) 0.05% Max have to controlled below these levels.
Melting Point
Melting point of SS400 is 1430 Degree Celsius
Table Ukuran dan Berat Nominal dan Harga Plat Besi:
Thick
 (mm) WxL (feet)  Weight  Price Rp
1.2 mm x 4×8 28 Kg
1.35 mm x 4×8 31.5 Kg
1.4 mm x 4×8 33 Kg
1.5 mm x 4×8 35 Kg
1.6 mm x 4×8 37.5 Kg
1.8 mm x 4×8 42 Kg
1.9 mm x 4×8 45 Kg
2 mm x 4×8 46.7 Kg
2.1 mm x 4×8 49 Kg
2.3 mm x 4×8 54 Kg
2.5 mm x 4×8 58.3 Kg
2.6 mm x 4×8 60.7 Kg
2.8 mm x 4×8 65.3 Kg
2.9 mm x 4×8 67.7 Kg
3 mm x 4×8 70 Kg
3.2 mm x 4×8 74.7 Kg
3.6 mm x 4×8 84 Kg
3.8 mm x 4×8 88.7 Kg
4 mm x 4×8 93.32 Kg
4.5 mm x 4×8 105 Kg
4.8 mm x 4×8 112 Kg
5 mm x 4×8 117 Kg
5.8 mm x 4×8 135.32 Kg
6 mm x 4×8 140 Kg
8 mm x 4×8 187 Kg
9 mm x 4×8 210 Kg
10 mm x 4×8 233.3 Kg
11 mm x 4×8 256.62 Kg
12 mm x 4×8 280 Kg
13 mm x 4×8 303.3 Kg
14 mm x 4×8 326.62 Kg
15 mm x 4×8 350 Kg
16 mm x 4×8 373 Kg
18 mm x 4×8 420 Kg
19 mm x 4×8 443.3 Kg
20 mm x 4×8 467 Kg
21 mm x 4×8 490 Kg
22 mm x 4×8 513.3 Kg
24 mm x 4×8 560 Kg
25 mm x 4×8 583.3 Kg
28 mm x 4×8 653.24 Kg
30 mm x 4×8 700 Kg
31 mm x 4×8 723.3 Kg
32 mm x 4×8 747 Kg
38 mm x 4×8 887 Kg
40 mm x 4×8 933.2 Kg
42 mm x 4×8 980 Kg
45 mm x 4×8 1050 Kg
50 mm x 4×8 1167 Kg
65 mm x 4×8 1516.5 Kg
75 mm x 4×8 1750 Kg
80 mm x 4×8 1870 Kg
85 mm x 4×8 1983.1 Kg
90 mm x 4×8 2100 Kg
100 mm x 4×8 2333 Kg

Beyond Steel Equivalent

Beyond-steel Comparison

Thyssen JIS
AISI Bohler ASSAB Atlas DIN
Balfour/ Rochling
Thyssen 1191 S45C 1045 EMS45 760 CM/ RMS30 CK45/ C45 1040/ 45
Thyssen 7225 SCM440 4140 VCL140 709 SPS 42CrMo4 SD19/ 4140
Thyssen 6582 SNCM439 4340 VCN150 705 Ultimo 200 34NiCrMo6 SD50 MONIX15
Thyssen 6580 Moulrex A
Thyroplast 2311 P20
Thyroplast 2312 P20+S Starmould Ultimo 200 PM53
Thyroplast 2767 AHT28
8620 SNCM220 8620 EPB100 En351 Impacto SD16 SD16B
En36A SNC815 3310 E200ES Special En36 Super Impacto SD51
En39B SNCM815
Thyroplast 2764 P21
Thyssen 2379 SKD 11 D2 X155Cr VMo1221
Thyssen 2344 SKD 61 H13 X40CrMoV51
Thyssen 2510 SKS 3 O1 100MnCrW4

The Classification of the Steel

Iron System

Specification

JIS Standards

AISI/ASTM Standards

Low Temperature
Carbon Steel
&
Low Alloy Steel

Low Temperature
Carbon Steel

S10C

AISI 1010

S15C

AISI 1015

S20C

AISI 1020

S25C

AISI 1025

S35C

AISI 1035

S45C

AISI 1045

S55C

AiSI 1055

Cr Steel

SCr 415

Cr-Mo Steel

SCM 415

SCM 435

AISI 4135

SCM 440

AISI 4140

Ni-Cr Steel

SNC 415

SNC 631

Ni-Cr-Mo Steel

SNCM 220

AISI 8620

SNCM 439

AISI 4340

Stainless Steel
&
Heat Resistant Steel

13Cr Steel

SCS 1 (SUS 410)

ASTM A217-CA15

SCS 2 (SUS 420 J2)

ASTM A743-CA40

17Cr Steel

SUS 440 C

AISI 440C

17-4PH

SCS 24 (SUS 630)

ASTM A 747-CB7CU1

18Cr-8Ni Steel

SUS 303

AISI 303

SCS 13 (SUS 304)

ASTM A351-CF8

SCS 14 (SUS 316)

ASTM A351-CF8M

SCS 316L

ASTM A351-CF3M

Heat Resistant Steel

SCH 13

ASTM A297-HH

SCH 22

ASTM A351-HK 40

Tool Steel

Carbon Tool Steel

SK 5

AISI W 1-8

SK 3

AISI W 1-10

Low Alloy Tool Steel

SKS 3

SKD 11

AISI D2

SKD 61

AISI H13

Penelusuran Terkait: persamaan besi/baja,equivalent steel, spesifikasi terdekat,nearest equivalent,japan standard steel,europe standard steel

AISI Standards

AISI 1010
AISI 1015
AISI 1020
AISI 1025
AISI 1035
AISI 1045
AISI 1055
AISI 303
AISI 4135
AISI 4140
AISI 8620
AISI 4340
AISI 440C
AISI W 1-8
AISI W 1-10
AISI D2
AISI H13

ASTM Standards

ASTM A217-CA15
ASTM A743-CA40
ASTM A 747-CB7CU1
ASTM A351-CF8
ASTM A351-CF8M
ASTM A351-CF3M
ASTM A297-HH
ASTM A351-HK 40