Harga Baja VCN

Steel VCN 150

Characteristics
It has high hardenability and is capable of giving good properties in large sections. It is relatively free from temper brittleness and retains useful machinability at relatively high hardness.

Equivalent VCN 150

Thyssen 6582, DIN 34NiCrMo6, ASSAB 705, JIS SMCM 431, AISI 4340

Availability
Round bar

Chemical Composition (%)

C Si Mn P S Ni Cr Mo
0.38–0.43 0.20–0.35 0.60–0.80 0.40 Max 0.040 Max 1.65–2.00 0.70–0.90 0.20-0.30

Mechanical Properties
Hardening Temp : 820 – 850 C
Ouenching Medium : Oil
Hardness as Supplied : 220 – 250 BHN,
Sizes Available : 20mm – 300mm

Applications
Automotive crankshafts and rear axle shafts, aircrafts crankshafts, Connecting Rods, Propeller Hubs, Gears, Drive shafts, Landing gear parts and heavy duty parts of rock drill

Lebih Detail »

Related Machinery Steel:

Iklan

Harga AISI 1045 Steel

AISI 1045 Steel Roundbar

Characteristic
AISI 1045 Steel is a medium strength steel. Suitable for shafts studs, keys etc. Available as rolled or normalised. Supplied as square bar, or round bar or flat. They are excelling in weldability & machinability , and they can be subjected to various heat treatments. Based on JIS G 4051-2009
AISI 1045 Steel Standard and Grade: JIS S45C DIN1.1151 is typical for flame hardening, and can produce a surface hardness of 500 BHN to a depth of 0.10 in this applies particularly to shafts and gears

Availability
Round bar, Flat

Size

Round Bar: Φ 3.2 – 400mm

Flat: 10 – 90 mm & 205 – 305mm or

Mechanical Properties
* Density (kg/m3) 7700-8030
* Young’s Modulus (GPa) 190-210
* Tensile Strength (Mpa) 569 (Standard) 686 (Quenching, Tempering)
* Yield Strength (Mpa) 343 (Standard) 490 (Quenching, Tempering)
* Poisson’s ratio 0.27-0.30

Hardness
Brinell Hardness (HB) 160-220 (Annealed)

Equivalents
DIN Equivalents for JIS S45C
C45, CK45, CF45, CQ45

ASTM Equivalents for JIS S45C
ASTM A29 , ASTM A510 , ASTM A519 , ASTM A576 , ASTM A682

SAE Equivalents for JIS S45C
SAE J403 , SAE J412 , SAE J414

AISI Equivalents for JIS S45C
AISI 1045, AISI 1046

EN Equivalents for JIS S45C
EN-8 / BS 970 080M40,Thyssen 1191, ASSAB 760

Chemical Composition

C Si Mn P S
0.42–0.48 0.15–0.35 0.6–0.9 0.030 Max 0.035 Max

Heat Treatment
The following temperature ranges are applicable for the respective heat treatment operations.
Full Annealing 800 – 850°C
Normalising 840 – 880°C
Hardening 820 – 860°C
Quenching medium Water or Oil
Tempering 550 – 660°C

Melting Point
Melting point: 1520 Degree Celsius

Applications

Standard punch head, special punch head and thread rolling tool requiring high precision, long service and abrasion resistance. Various machining tools, e. G. Lathe bit, milling cutter, drill bit, screw tap, round saw and other metal machining tools and wood machining tools. Also suitable for manufacture of forming tools, e. G. Cold extrusion head, extrusion die, punch dies of long service life, and plastic molds of high precision and long service life.

For further info Send by email to: sales@beyond-steel.com
Untuk informasi stock dan update harga terbaru
silahkan menghubungi sales team kami

Related Machinery Steel:

Stainless Steel 310

Product : AISI 310
Kategori: Stainless Steel
Grades : Chromium-Nickel steel
Standard: Austenitic

Characteristic
AISI 310 is an Austenitic Standard grade Stainless Steel. It is commonly called AISI Type 310 Chromium-Nickel steel.

Stainless Steel 310 Technical Data

Chemical Composition: (%)

C Mn Si Cr Ni P S
0.25 2.00 1.50 24.0-26.0 19.0-22.0 0.045 0.03

Equivalent:
France: AFNOR Z 12 CNS 25.20
Germany: DIN 1.4841
Italy: UNI X 16 CrNiSi 25 20 , UNI X 22 CrNi 25 20
Japan: JIS SUS 310
United Kingdom: B.S. 310 S 24
United States: AMS 5694 , AMS 5695 , ASME SA182 , ASME SA213 , ASME SA249 , ASME SA312 , ASME SA358 , ASME SA403 , ASME SA409 , ASTM A167 , ASTM A182 , ASTM A213 , ASTM A249 , ASTM A276 , ASTM A312 , ASTM A314 , ASTM A358 , ASTM A403 , ASTM A409 , ASTM A473 , ASTM A511 , ASTM A580 , ASTM A632 , FED QQ-S-763 , FED QQ-S-766 , FED QQ-W-423 , FED STD-66 , MIL SPEC MIL-S-862 , SAE 30310 , SAE J405 (30310) , UNS S31000

Mechanical Properties
Density (×1000 kg/m3) 8
Poisson’s Ratio 0.27-0.30
Elastic Modulus (GPa) 200
Tensile Strength (Mpa) 515
Yield Strength (Mpa) 205
Elongation (%) 40
Reduction in Area (%) 50
Hardness (HRB) 95 (max)

Physical Properties
Thermal Expansion (10-6/ºC) 15.9
Thermal Conductivity (W/m-K) 14.2
Specific Heat (J/kg-K) 500
Electric Resistivity (10-9W-m) 780

Applications

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment

Product Stainless Steel:

Stainless Steel 304

Dear valued customers,

Beyond-Steel menjual Stainless Steel 304 acerinox,Jindal, Heisei, Outokumpu import plat, sheet, roundbar dan chanel dengan ukuran dan ketebalan bervariasi. Untuk informasi stock dan harga silahkan hubungi kami:

Tel  : +62-021-2986 1684

Fax : +62-021-2986 1684

Mobile: +62-0819 0804 5114

E-mail: sales@beyond-steel.com

Characteristic Grades 304

Stainless steel grade 304 is the most versatile and widely used stainless steel. It is still sometimes referred to by its old name 18/8 which is derived from the nominal composition of type 304 being 18% chromium and 8% nickel. Stainless steel types 1.4301 and 1.4307 are also known as grades 304 and 304L respectively.

Stainless steel 304 is an austenitic grade that can be severely deep drawn. This property has resulted in 304 being the dominant grade used in applications like sinks and saucepans.

Stainless steel 304L is the low carbon version of 304. It is used in heavy gauge components for improved weldability. Some products such as plate and pipe may be available as “dual certified” material that meets the criteria for both 304 and 304L. 304H, a high carbon content variant, is also available for use at high temperatures.

Property data given in this document is typical for flat rolled products covered by ASTM A240/A240M. ASTM, EN or other standards may cover products sold. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this datasheet.

Availability

Stainless steel 304 is available in Sheet, Bar, Wire, Rod, Strip, tube, pipe, and Channel, For all stock availability contact Sales.

Stainless steel 304 Sheet

Stainless steel 304 Plate

Stainless steel 304 Rod

Stainless steel 304 Tube

Stainless steel 304 Pipe

Stainless steel 304 Channel

Stainless Steel 304 Technical Data

Chemical Composition (%)

C : 0.05 – 0.08

Si : <= 1.0

Mn: <= 2.00

Ni : 8.00 – 11.00

Cr : 18.00 – 20.00

Tensile Strength (0.2%) : >= 53 Kgf/MM2

Yield Strength : >= 21 Kgf/MM2

Elongation : >= 40%

Hardness (HB) : <= 187 HB

Corrosion Resistance

304 has excellent corrosion resistance in a wide variety of environments and when in contact with different corrosive media. Pitting and crevice corrosion can occur in environments containing chlorides. Stress corrosion cracking can occur at temperatures over 60°C.
 
Heat ResistanceJustify Full304 has good resistance to oxidation in intermittent service up to 870°C and in continuous service to 925°C. However, continuous use at 425-860°C is not recommended if corrosion resistance in water is required. In this instance 304L is recommended due to its resistance to carbide precipitation.Where high strength is required at temperatures above 500°C and up to 800°C, grade 304H is recommended. This material will retain aqueous corrosion resistance.
 
Fabrication

Fabrication of all stainless steels should be done only with tools dedicated to stainless steel materials. Tooling and work surfaces must be thoroughly cleaned before use.These precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

Cold Working

304 stainless steel readily work hardens. Fabrication methods involving cold working may require an intermediate annealing stage to alleviate work hardening and avoid tearing or cracking. At the completion of fabrication a full annealing operation should be employed to reduce internal stresses

Hot Working

Fabrication methods, like forging, that involve hot working should occur after uniform heating to 1149-1260°C. The fabricated components should then be rapidly cooled to ensure maximum corrosion resistance.

Heat Treatment

304 stainless steel cannot be hardened by heat treatment. Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

Machinability

304 stainless steel has good machinability. Machining can be enhanced using the following rules:

  • Cutting edges must be kept sharp. Dull edges cause excess work hardening.
  • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.
  • Chip breakers should be employed to assist in ensuring swarf remains clear of the work
  • Low thermal conductivity of austenitic alloys results in heat concentrating at the cutting edges. This means coolants and lubricants are necessary and must be used in large quantities.
Welding

Fusion welding performance for type 304 stainless steel is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel. For 304L the recommended filler is 308L. Heavy welded sections may require post-weld annealing. This step is not required for 304L. Grade 321 may be used if post-weld heat treatment is not possible.

 

Tabel Ukuran dan Berat Plat stainless steel 304 4’x8′ Beyond-steel Indonesia:

Stainless Steel Size  Berat (Kg)
Plate 304 1 mm x 4′ x 8′ 23.6 Kg
Plate 304 2 mm x 4′ x 8′ 47.2 Kg
Plate 304 3 mm x 4′ x 8′ 70.8 Kg
Plate 304 4 mm x 4′ x 8′ 94.4 Kg
Plate 304 5 mm x 4′ x 8′ 118 Kg
Plate 304 6 mm x 4′ x 8′ 141.6 Kg
Plate 304 8 mm x 4′ x 8′ 188.8 Kg
Plate 304 10 mm x 4′ x 8′ 236 Kg
Plate 304 12mm x 4′ x 8′ 283.2 Kg

Applications

304 stainless steel is typically used in:

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment
  • Springs, nuts, bolts and screws
  • Medical implants

Related Stainless Steel:

Creusabro 4800 & 8000

Characteristic

For wear and tear which is not only caused by impact and friction, we provide CREUSABRO 4800 and CREUSABRO 8000. These products have TRIP (Transformation Induced by Plasticity) character and micro carbides that make this product have an active surface resistance, so that this material can last better if there is an impact. This product o can also be used in medium temperature 250–450 C, where other resistance product which generates from water quenched process usually will not be functioning optimally.

Creusabro 4000
The new Creusabro concept-excellent ability to work harden and contribution of micro carbides-gives Creusabro 4000 high wear resistance, on average 4 times higher than ordinary mild steel and 30 % higher than conventional 4000 BHN water quenched steel.

To ease in fabricating, Creusabro 4000 is supplied by approximately 360 HB hardness. After the fabrication, the hardness of Creusabro 4000 can be reach 420 HB.

Chemical Composition:

C : 0.20 max
Mn : 1.40
Cr : 0.85 min
Mo : 0.10 min
Ni : 0.30
S : 0.010 max
P : 0.018 max

Applications:
Mines: Extractors, Unloaders, Spiral Chutes. Crusher, Grinders, Screens, Conveyor
Quarries and Construction Earth Moving: Shovels, Diggers, Graders, Bulldozers, Dumpers, Dredging machines, Crushers, Grinders, Screens, Hoppers, Mixers, Molds for concrete aggregates
Cement Plants, Refractory Products: Crushers, Hoppers, Chutes, Cyclone, Wheel Excavator Buckets Metallurgical Plant, Scrap recovery, etc

The Creusabro concept-excellent ability to work harden and the supplementary contribution of microcarbides, already used in Creusabro 4000 has been improved in the Creusabro 8000. this grade takes advantage of an additional metal working process: the TRIP effect (Transformation Induce by Plasticity). The combination of this properties give to the Creusabro 8000 an exceptional wear resistance in heavy plates with uniform properties throughout the thickness around 8 times that of the standard mild steel (A572 G65 grade). The properties in extreme conditions are 50% superior to standard water quenched steel (hardness 500HB).

Creusabro 8000

Creusabro 8000 is supplied with the hardness of 420 HB in order to easy the fabrication. After fabrication, the hardness of Creusabro 8000 can reach 540 HB.

Chemical Compositions:
C Mn Cr Mo Ni S P
0.280 max 1.60 max 1.60 max 0.20 min 0.40 0.005 max 0.015 max

Applications:

Mines, Coal mines: Extracting and load equipment, Hopper lateral liner plate, Helical gravity conveyor.
Quarries and Construction Earth Moving: Blades, Outside Stiffeners, Under teeth pads of loaders and shovel dippers, Crushers and Mills lateral armor plate, Feed crown-wheel, Sprocket-wheal.
Cement Plants: Liners for drier-tubes, Buckets, Hoppers, Clinker cooler outlet shields.
Iron and Steel Industry: Scrap recovery, Brick works, Agricultural equipment, etc.

beyond-steel indonesia, distributor creusabro indonesia jual creusabro, ukuran creusabro,harga creusabro,diameter creusabro,dia. creusabro,beli creusabro,distributor creusabro,tebal creusabro,berat creusabro,pabrik creusabro, stockist creusabro,grade creusabro, suplier creusabro,chemical composition creusabro, equivalent of creusabro, mechanical properties creusabro, physical properties creusabro, properties of creusabro, hrc creusabro,thickness creusabro, hardness creusabro

Plat FORA 400

Characteristic

FORA 400 is a water quenched maternistic steel, with a typical hardness of 400HB (42,5HRC), constituting a real answer to abrasive wear. Thanks to its toughness, its elevated hardness, its high yield strength, FORA 400 can be use wherever a wear resistance to wear by sliding or by moderate impacts is required. Moreover, FORA 400 is very easily welded and has a good forming properties thereby contributing to ease of fabrication.

Compared to conventional steels, such as S355, FORA 400 offers a real benefit to the equipment life times and permits a signifiant reduction in he design thickness since its wear resistance is up to 3 times longer than S355 grade.

Moreover, FORA 400 is very easily welded and has a good forming properties thereby contributing to ease of fabrication. This steel is particulary suitable for applications in quarries, construction industry, mines, cement plants, the iron and steel industry, etc.

Chemical Composition
C Mn Cr Mo S max P max
0.13 1.2 0.5 0.25 0.01 0.02

Applications
Quarries and Construction Earth Moving: Skimmers, crushers, screens, bunkers, bulldozers, etc.
Cement Plants: Buckets, crushers, bunkers, etc.
Mines, Coal mines: Excavator, winding and discharging machines, conveyors, etc.
Iron and steel industry: Bunkers, various casing, guide and shifting plates, etc.

Beyond-Steel Indonesia, distributor FORA 400 Indonesia jual FORA 400, ukuran FORA 400,harga FORA 400,diameter FORA 400,dia. FORA 400,beli FORA 400,distributor FORA 400,tebal FORA 400,berat FORA 400,pabrik FORA 400, stockist FORA 400,grade FORA 400, suplier FORA 400,chemical composition FORA 400, equivalent of FORA 400, mechanical properties FORA 400, physical properties FORA 400, properties of FORA 400, hrc FORA 400,thickness FORA 400, hardness FORA 400

Related Wear Plates:

Steel 6582

Product: Thyssenkrupp 6582

Kategori: High Tensile Nickel Chrome Steel

Characteristics
It has high hardenability and is capable of giving good properties in large sections. It is relatively free from temper brittleness and retains useful machinability at relatively high hardness.

Equivalent Thyssen 6582
AISI 4340, DIN 34NiCrMo6, ASSAB 705, VCN 150, JIS SMCM 431, Atlas Ultimo 200

Availability
Round bar

Chemical Composition (%)

C Si Mn P S Ni Cr Mo
0.38-0.43 0.20-0.35 0.60-0.80 0.40 Max 0.04 Max 1.65-2.00 0.70-0.90 0.20-0.30

Mechanical Properties

Hardening Temp : 820 – 850 C
Ouenching Medium : Oil
Hardness as Supplied : 220 – 250 BHN,
Sizes Available : 20mm – 300mm

Applications
Automotive crankshafts and rear axle shafts, aircrafts crankshafts, Connecting Rods, Propeller Hubs, Gears, Drive shafts, Landing gear parts and heavy duty parts of rock drill

Product Machinery Steel: