Jual Quend 700

Description
Quend 700 is extra high strength structural steel produced as quenched and tempered with a minimum yield strength of 700 MPa. Quend 700 complies with the requirements corresponding to the S690QL given in the EN 10025-6 standard, where impact toughness is guaranteed at -40 °C.

Availability
Quend 700 is currently supplied in the following range:
• thickness: 8 – 25 mm
• width: 1500 – 3000 mm

Chemical Composition (%)

C Si Mn Cr Mo P Ni S B Nb V Ti Al N
 0.20 0.60 1.50 0.60 0.50 0.020 1.00 0.010 0.005 0.040 0.070 0.040 0.070 0.014

Mechanical Properties
Hardness (HBW) : 370 – 430
Charpy-V notch : 35 J
impact test (longitudinal at -40 °C)
Yield Strength (MPa): 700 Min
Tensile Strength (MPa): 780 – 930
Elongation (%): 14

Cutting
Quend 700 may be cut either by oxygen fuel, plasma and laser cutting without any restrictions

Welding
Welding of Quend 700 can be performed using any of the conventional welding methods available both as manual or automatic.

Application
Quend 700 is recommended for the following applications:
• truck chassis
• lifting and hoisting equipment
• handling equipment
• trailers

Related Carbon Steel:

Ympress Plate

Description
Ympress is the brand name for the series of hot-rolled High-Strength Low-Alloy steel produced by TMCP (Thermal Mechanical Control Process). Through customer focus the Ympress range has been continuously improved and widened to match the increasing requirements of our customers. Ympress delivers high strength steel with consistent properties, excellent surface quality and high formability. To ensure an optimum match with standards, all grades have been designed to meet or exceed specifications conform EN 10149.

Ympress offer a wide range of strength levels between S315MC up to S700MC and a broad dimensional range with gauges between 1.5 and 20 mm and widths up to 2070 mm. Because of the wide dimensional range and the number of strength levels included in the Ympress brand, Ympress can be used for many applications ranging from construction profiles to crane booms.

Chemical Composition

C Mn Si P S Altot Nb V Ti Mo
Guaranteed ≤ 0.08 ≤ 1.90 ≤ 0.15 0.003 ≤ 0.05 ≤ 0.015 ≤ 0.09 ≤ 0.01 ≤ 0.15 ≤ 0.02
Typical CEV 0.35
Typical Pcm 0.16 (Japanese welding society standard)

Mechanical Properties

Thickness ReH in MPa Rm in MPa A80 in % Adp5 in %
Typical 2 – 3 mm 825 840 13
4 – 8 mm 800 845 19
8 – 10 mm 750 825 18
Guaranteed ≥ 690 750 – 950 ≥ 12 ≥ 14
Bend 0.5t for thickness ≤ 3mm
1t for thickness ≤ 6mm
1.5t for thickness > 6mm

Ympress Benefits

The consistency in chemical composition and production conditions provide the basis for the consistency in product properties of Ympress. Through its properties Ympress contributes to an optimum and efficient processing and high quality finished products.

  • Formability:
    The precise control of the sulphur content prevents the formation of MnS particles resulting in improved bending characteristics for Ympress. Even the use of a very small bending radius (0t) is possible for many strength levels. The guaranteed elongation levels are leading in the European industry.
  • Consistency:
    Ympress’ consistent properties and narrow gauge control ensure the same bending behaviour from sheet to sheet and from coil to coil. This reduces the intermediate setup times for tooling and increases efficiency.
  • Welding:
    The guaranteed low carbon equivalent allows Ympress to be welded trouble free with the commonly used welding methods. Pre- or post heating of the steel is therefore not necessary.
  • Galvanising:
    Most Ympress can directly be galvanised, the very low silicon content prevents the formation of surface defects by the Sandelin effect. For the highest strength levels E690TM and S700MC it is recommended to test the galvanising conditions first.
  • Laser cutting:
    For the optimisation of your laser cutting process we recommend the use of Ympress Laser. Ympress Laser is a superior product because of the low tensions in the material, the low silicon content and the extra high surface quality.
  • High surface quality:
    The low silicon content of all Ympress grades avoids the formation of so called ‘tiger stripes’ . The high quality surface can lead to fewer processing steps during manufacture.

Fabrication

The low carbon equivalent of Ympress makes it readily weldable and permits the use of high welding speeds. There is no need for pre-or post-welding treatment.

Adjacent to the weld a narrow Heat Affected Zone (HAZ) with a slightly decreased hardness is produced, however, with standard welding techniques this has no practical significance.

Tensile tests taken transverse to the weld show the same tensile strength as the parent material.

Stress relieving should be done in temperature ranges of 980° – 1080° F. Heating above this range reduces strength and should be avoided.

Application

Ympress combines high strength with excellent formability and weldability. It is used in applications such :

• Earth Moving Vehicles
• Large Cranes / Mobile Cranes
• Telescopic Booms

In these applications the high strength of steel is used to save weight and increase the load bearing capacity.

Product Wear Plates:

Stainless Steel 310

Product : AISI 310
Kategori: Stainless Steel
Grades : Chromium-Nickel steel
Standard: Austenitic

Characteristic
AISI 310 is an Austenitic Standard grade Stainless Steel. It is commonly called AISI Type 310 Chromium-Nickel steel.

Stainless Steel 310 Technical Data

Chemical Composition: (%)

C Mn Si Cr Ni P S
0.25 2.00 1.50 24.0-26.0 19.0-22.0 0.045 0.03

Equivalent:
France: AFNOR Z 12 CNS 25.20
Germany: DIN 1.4841
Italy: UNI X 16 CrNiSi 25 20 , UNI X 22 CrNi 25 20
Japan: JIS SUS 310
United Kingdom: B.S. 310 S 24
United States: AMS 5694 , AMS 5695 , ASME SA182 , ASME SA213 , ASME SA249 , ASME SA312 , ASME SA358 , ASME SA403 , ASME SA409 , ASTM A167 , ASTM A182 , ASTM A213 , ASTM A249 , ASTM A276 , ASTM A312 , ASTM A314 , ASTM A358 , ASTM A403 , ASTM A409 , ASTM A473 , ASTM A511 , ASTM A580 , ASTM A632 , FED QQ-S-763 , FED QQ-S-766 , FED QQ-W-423 , FED STD-66 , MIL SPEC MIL-S-862 , SAE 30310 , SAE J405 (30310) , UNS S31000

Mechanical Properties
Density (×1000 kg/m3) 8
Poisson’s Ratio 0.27-0.30
Elastic Modulus (GPa) 200
Tensile Strength (Mpa) 515
Yield Strength (Mpa) 205
Elongation (%) 40
Reduction in Area (%) 50
Hardness (HRB) 95 (max)

Physical Properties
Thermal Expansion (10-6/ºC) 15.9
Thermal Conductivity (W/m-K) 14.2
Specific Heat (J/kg-K) 500
Electric Resistivity (10-9W-m) 780

Applications

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment

Product Stainless Steel:

Stainless Steel 304

Dear valued customers,

Beyond-Steel menjual Stainless Steel 304 acerinox,Jindal, Heisei, Outokumpu import plat, sheet, roundbar dan chanel dengan ukuran dan ketebalan bervariasi. Untuk informasi stock dan harga silahkan hubungi kami:

Tel  : +62-021-2986 1684

Fax : +62-021-2986 1684

Mobile: +62-0819 0804 5114

E-mail: sales@beyond-steel.com

Characteristic Grades 304

Stainless steel grade 304 is the most versatile and widely used stainless steel. It is still sometimes referred to by its old name 18/8 which is derived from the nominal composition of type 304 being 18% chromium and 8% nickel. Stainless steel types 1.4301 and 1.4307 are also known as grades 304 and 304L respectively.

Stainless steel 304 is an austenitic grade that can be severely deep drawn. This property has resulted in 304 being the dominant grade used in applications like sinks and saucepans.

Stainless steel 304L is the low carbon version of 304. It is used in heavy gauge components for improved weldability. Some products such as plate and pipe may be available as “dual certified” material that meets the criteria for both 304 and 304L. 304H, a high carbon content variant, is also available for use at high temperatures.

Property data given in this document is typical for flat rolled products covered by ASTM A240/A240M. ASTM, EN or other standards may cover products sold. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this datasheet.

Availability

Stainless steel 304 is available in Sheet, Bar, Wire, Rod, Strip, tube, pipe, and Channel, For all stock availability contact Sales.

Stainless steel 304 Sheet

Stainless steel 304 Plate

Stainless steel 304 Rod

Stainless steel 304 Tube

Stainless steel 304 Pipe

Stainless steel 304 Channel

Stainless Steel 304 Technical Data

Chemical Composition (%)

C : 0.05 – 0.08

Si : <= 1.0

Mn: <= 2.00

Ni : 8.00 – 11.00

Cr : 18.00 – 20.00

Tensile Strength (0.2%) : >= 53 Kgf/MM2

Yield Strength : >= 21 Kgf/MM2

Elongation : >= 40%

Hardness (HB) : <= 187 HB

Corrosion Resistance

304 has excellent corrosion resistance in a wide variety of environments and when in contact with different corrosive media. Pitting and crevice corrosion can occur in environments containing chlorides. Stress corrosion cracking can occur at temperatures over 60°C.
 
Heat ResistanceJustify Full304 has good resistance to oxidation in intermittent service up to 870°C and in continuous service to 925°C. However, continuous use at 425-860°C is not recommended if corrosion resistance in water is required. In this instance 304L is recommended due to its resistance to carbide precipitation.Where high strength is required at temperatures above 500°C and up to 800°C, grade 304H is recommended. This material will retain aqueous corrosion resistance.
 
Fabrication

Fabrication of all stainless steels should be done only with tools dedicated to stainless steel materials. Tooling and work surfaces must be thoroughly cleaned before use.These precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

Cold Working

304 stainless steel readily work hardens. Fabrication methods involving cold working may require an intermediate annealing stage to alleviate work hardening and avoid tearing or cracking. At the completion of fabrication a full annealing operation should be employed to reduce internal stresses

Hot Working

Fabrication methods, like forging, that involve hot working should occur after uniform heating to 1149-1260°C. The fabricated components should then be rapidly cooled to ensure maximum corrosion resistance.

Heat Treatment

304 stainless steel cannot be hardened by heat treatment. Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

Machinability

304 stainless steel has good machinability. Machining can be enhanced using the following rules:

  • Cutting edges must be kept sharp. Dull edges cause excess work hardening.
  • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.
  • Chip breakers should be employed to assist in ensuring swarf remains clear of the work
  • Low thermal conductivity of austenitic alloys results in heat concentrating at the cutting edges. This means coolants and lubricants are necessary and must be used in large quantities.
Welding

Fusion welding performance for type 304 stainless steel is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel. For 304L the recommended filler is 308L. Heavy welded sections may require post-weld annealing. This step is not required for 304L. Grade 321 may be used if post-weld heat treatment is not possible.

 

Tabel Ukuran dan Berat Plat stainless steel 304 4’x8′ Beyond-steel Indonesia:

Stainless Steel Size  Berat (Kg)
Plate 304 1 mm x 4′ x 8′ 23.6 Kg
Plate 304 2 mm x 4′ x 8′ 47.2 Kg
Plate 304 3 mm x 4′ x 8′ 70.8 Kg
Plate 304 4 mm x 4′ x 8′ 94.4 Kg
Plate 304 5 mm x 4′ x 8′ 118 Kg
Plate 304 6 mm x 4′ x 8′ 141.6 Kg
Plate 304 8 mm x 4′ x 8′ 188.8 Kg
Plate 304 10 mm x 4′ x 8′ 236 Kg
Plate 304 12mm x 4′ x 8′ 283.2 Kg

Applications

304 stainless steel is typically used in:

  • Sinks and splashbacks
  • Saucepans
  • Cutlery and flatware
  • Architectural panelling
  • Sanitaryware and troughs
  • Tubing
  • Brewery, dairy, food and pharmaceutical production equipment
  • Springs, nuts, bolts and screws
  • Medical implants

Related Stainless Steel:

Harga Plat Durinox F12N-304

Dear valued customers,

Beyond-Steel menjual plat Durinox stainless steel Grade import dengan ketebalan bervariasi. Untuk informasi stock dan harga silahkan hubungi kami:
Tel  : +62-021-2986 1684
Fax : +62-021-2986 1684
Mobile: +62-0818 0817 1467
E-mail: sales@beyond-steel.com

Characteristic

DURINOX ™ is developed mainly for the agricultural industries where corrosion and abrasion are often the major source of cost and quality problems.

Durinox™ is a registered trademark of Beyond-steel covering a range of ferritic stainless steel grades.

Durinox™ offers superior and low-cost solution to carbon steels and, in many cases, to austenitic stainless steels.

Durinox™ is developed mainly for the agricultural industries where corrosion and abrasion are often the major source of cost and quality problems. It is also often the case that many of the plants in agricultural industries were originally designed with carbon steels because of its low cost. In many cases, this proved a false
economy, since carbon steel performs poorly against corrosion and abrasion.

Durinox™ stainless steels is an excellent choice for agricultural industries as it is both chemically inert in contact with food and produce and also biologically inert which reduce the risk of micro-organism colony growth.

Durinox™ offers the following benefits compared to austenitic stainless steels and carbon steel:

  • Similar thermal expansion to carbon steel and lower compared to austenitic stainless steels, and there-
    fore it distort less when heated
  • Thermal conductivity that is much higher than austenitic stainless steels
  • High temperature oxidation resistance, they are less prone to scaling
  • Its mechanical properties are very similar to carbon steel making it easy to cut and work without the need of specialized tools. They are also less prone to spring back compared austenitic stainless steels
  • It is not prone to stress corrosion cracking
  • They can be used in temperatures to up to 600°C which is far better than carbon steel and is more than
    sufficient for most agricultural industries

Availability

Plat Durinox™ F12N is available as hot rolled sheet and plates with no. 1 (as rolled) finish.

Product Thickness Size (WxL)
Plat Durinox 1.6 mm x 1500 x 6000 mm
Plat Durinox 2 mm x 1500 x 6000 mm
Plat Durinox 3 mm x 1500 x 6000 mm
Plat Durinox 4 mm x 1500 x 6000 mm
Plat Durinox 5 mm x 1500 x 6000 mm
Plat Durinox 6 mm x 1500 x 6000 mm
Plat Durinox 8 mm x 1500 x 6000 mm
Plat Durinox 10 mm x 1500 x 6000 mm
Plat Durinox 12 mm x 1500 x 6000 mm
Plat Durinox 16 mm x 1500 x 6000 mm
Plat Durinox 20 mm x 1500 x 6000 mm
Plat Durinox 25 mm x 1500 x 6000 mm

Mechanical Properties

Grade Tensile
Strength
(MPa) min
Yield
Strength
(MPa) min
Elongation
(%)
min
Hardness
Brinell
(HB) min
Cold Bend
Transverse direction
Bend radius = 1T
F12N 455 275 18 220
SUS 304 515 250 40 200 180°
Mild Steel 375 250 20 180 180°

Chemical Composition

C Mn Si P S Cr Ni
0.03 0.15 1.00 0.025 0.005 10.5 – 12.5 0.3 – 1.0

Physical Properties

Grade Density
(g/cm3)
Average thermal
expansion
Coefficient from
0°C to
Thermal
Conductivity
100oC
(W.m.K)
Electrical
resistivitynΩ.m
Specific
Heat(j/kg.oK)
Young
Modulus
(GPa)
100°C
µ/m.°C
538°C
µ/m.°C
F12N 7.7 10.8 11.9 23 580 460 220
SUS 304 8.0 17.2 18.4 16.2 720 500 193
SUS 316 8.0 15.9 17.5 16.2 740 500 193
Mild Steel 7.8 12.2 14.3 57.8 142

Related Stainless Steel:

Besi Cor 50mm

Besi Cor 50mm

Beyond-Steel one of the steel & iron wholesaler in Indonesia menjual aneka besi beton polos dan ulir berbagai ukuran, mulai dari ukuran 6 mm – 50 mm, Panjang standard 12 meter. Melayani pengiriman Jabodetabek & luar kota

Product: Besi Beton Polos & Ulir
Kategori: Structural Steel
Standard: SNI
Brand: KS, GG, Master, CS, IS, STD,  AS, TI, TY, AIS

Tabel Ukuran, Berat & Harga Besi Beton Standard SNI  Klik disini »

Info pemesanan hubungi:
» Tel : +62-021-3293 5972
» Fax: +62-021-8837 6742
» Mobile: +62-085 880 446 226
» E-mail: sales@beyond-steel.com
» Attn: Mr.Mugiyono
» Website : www.beyond-steel.com

Product  Structural Steel:

Besi Cor 40mm

Besi Cor 40mm

Beyond-Steel one of the steel & iron wholesaler in Indonesia menjual aneka besi beton polos dan ulir berbagai ukuran, mulai dari ukuran 6 mm – 50 mm, Panjang standard 12 meter. Melayani pengiriman Jabodetabek & luar kota

Product: Besi Beton Polos & Ulir
Kategori: Structural Steel
Standard: SNI
Brand: KS, GG, Master, CS, IS, STD,  AS, TI, TY, AIS

Tabel Ukuran, Berat & Harga Besi Beton Standard SNI  Klik disini »

Info pemesanan hubungi:
» Tel : +62-021-3293 5972
» Fax: +62-021-8837 6742
» Mobile: +62-085 880 446 226
» E-mail: sales@beyond-steel.com
» Attn: Mr.Mugiyono
» Website : www.beyond-steel.com